|
|
| Proximity
Sensors |
|
DJ2-G
|
| Economical
solution for detecting metal in front of a sensing
surface; metal objects adjacent to or behind will not
normally be detected. Features a pre-wired 17 foot cable
assembly, zero-sensing capability and small package size.
Can be used with a single projection head or a 10DP gear. | manual
& specs | new
manual & specs |
| BI2-S12 |
| 3
wire DC inductive proximity sensor. Features include short
circuit, overload protection and output LED. Meets NEMA
ratings 1, 3, 4, 6, 13, and IEC IP67. | manual
& specs |
|
SE-G
|
| A
solid state 3 wire proximity (switching) sensor specially
designed for gear sensing. Provides a square wave output
signal and indicates detection via LED indicator (gear
pitch must be between 16.93 and 25.4). | manual
& specs |
| MCS-3109 |
| Complimentary
(NPN-NO and NPN-NC) proximity sensor normally used in
high-vibration areas and where a greater sensing distance
is required. | manual
& specs |
|
|
|
|
| Magnetic
Pick-Up Sensors |
| MP-10 |
| General-purpose
economy model. Designed to mount in a 5/8”-18 threaded hole
with included securing jam nut. 10 foot cable included. | manual
& specs |
| 3030AN |
| Magnetic
pick-up with Amphenol connector; requires sensor cable
assembly. This general-purpose unit is designed to mount in a
5/8”-18 threaded hole and is provided with a jam nut for
sensor securing. | manual
& specs |
| 3070A |
| Specifically
engineered for use in the oil and petrochemical industries,
this stainless steel sensor is completely sealed and
explosion-proof. Low impedance allows for transistor circuit
input. When mated with conduit, it provides positive
protection against damage due to water, high humidity, oil,
dirt, dust, or corrosive liquids. UL and CSA listed for Class
I-Group C & D hazardous locations. Class II-Group E, F,
& G. | manual
& specs |
|
|
|
| Length
and Linear Speed Measuring Sensors |
| LSL-3A2 |
| Measures in
0.1 M/YD with an output signal in one direction. | manual
& specs |
| LSL-3A3 |
| Measures in
0.1 M/YD with bi-directional output signal. | manual
& specs |
| |
|
|
|
| Photo-Reflective
Sensors |
| RS-220HR |
| A
general purpose sensor, featuring an operating range up to
500Hz. Consists of an LED infrared light source sensing device
and amplifier contained in a heavy-duty housing. Includes an
indicator lamp for initial alignment purposes. | manual
& specs |
| MCS-625 |
| Consists
of a LED infra-red light source sensing device and amplifier
contained in a heavy-duty housing. For initial alignment
purposes, a small indicator lamp is mounted in the top of the
sensor housing. The MCS-625 has an open collector output and
requires a pull up resistor. | manual
& specs |
| MCS-655 |
| Incorporates
a complimentary switching voltage output (light/dark
activated) that operates up to 333Hz. An LED is mounted in the
back of the unit with sensitivity adjustment. | manual
& specs |
|
|
|
| Rotary
Pulse Generators |
| RE1B-60C |
| 60
digital output pulses per shaft revolution. Maximum speed:
5000 RPM. | manual
& specs |
| RE1B-600C |
| 600
digital output pulses per shaft revolution. Maximum speed:
3000 RPM. | manual
& specs |
| RE1B-1000C |
| 1000
digital output pulses per shaft revolution. Maximum speed:
1800 RPM. | manual
& specs |
| RE2B-30C,
RE2B-60C, RE2B-600C |
| Dual
(90° out of phase) digital pulses for quadrature
applications. Also a zero position (third output) is
available to mark the reference position of the shaft.
Maximum speed: 3000 RPM and 5000 RPM respectively.
| RE2B-30C
manual & specs | RE2B-600C
manual & specs |
|
|
