Fluke's compact answer to pressure calibration
Of course size matters -and so does weight. Particularly if you have to carry your test tools around with you. The Fluke 718 pressure calibrators are about a third of the size of comparable instruments and weigh just one kilogram (two pounds). With its built-in pressure/vacuum pump, the Fluke 718 offers a complete solution for on-site pressure maintenance and calibration. Out in the field, you'll really notice the difference.
The Fluke 718 Pressure Calibrator is a complete, self-contained calibration solution, the 718 offers:
* Built-in pressure / vacuum hand pump, with vernier and bleed valve
* New switch test function captures set, reset and dead band.
* Pressure measurement to 0.05% of full span, using an internal pressure sensor
* Pressure measurement to 10,000 PSI, 700 bar using any of the Fluke-700Pxx Pressure Modules
* Current measurement with 0.025% accuracy and 0.001 mA resolution
* Wide range of selectable measurement units for pressure
* 24 volt loop power supply
* Min-Max Hold and damp functions
* 1/8 inch NPT female pressure fitting
* Simple, push-button user interface
* Compact size and weight
* 3 year warranty
| Measurement Accuracy | | Pressure | | Fluke 718 30G | | | | | Range: | -12 to 30 PSI, -850 mbar to 2 bar (internal sensor) Over Pressure 3xFS | | Resolution: | 0.001 psi, 0.1 mbar | | Accuracy: | 0.05% full scale | | Functions: | Zero, Min, Max, Hold, Damp | | Note: for use with non-corrosive gasses | | | | Fluke 718 100G | | | | | Range: | -12 to 100 PSI, -850 mbar to 7 bar (internal sensor) Over Pressure 3xFS | | Resolution: | 0.01 psi, 1 mbar | | Accuracy: | 0.05% of full scale | | Functions: | Zero, Min, Max, Hold, Damp | | Note: for use with non-corrosive gasses | | | | Fluke 718 series | | | | | via pressure module connector | | Range: | 29 pressure modules, 0-1 inH20 to 10,000 psi, 2.5 mbar to 700 bar | | Over pressure per pressure module specs | | Resolution: | Per pressure module specs | | Accuracy: | To 0.025% of full span, per pressure module specs | | Functions: | Zero, Min, Max, Hold, Damp | | Note: media compatibility per pressure module specs, | | | | Source Pressure, built in pump | | | Range: | -12 PSI or -820 mbar to full scale | | | | Supported Pressure Units; psi, in. H20 (4 °C), in. H20 (20 °C), cm H20 (4 °C), | | cm H20 (20 °C), bar, mbar, kPa, inHg, mmHg, kg/cm | | | Specifications | | Loop Power | | Range: | 24 V dc | | Accuracy: | +/- 10% | | Note: Drive; 20 mA into 1000 O for battery >6.8V; 700 O for battery 5.8 to 6.8 V | | | Measure Accuracy: | | Range: | 0 to 24 mA | | Resolution: | 0.001 mA | | Accuracy: | 0.025% + 1 count | | | Display | | LCD, 5 digit pressure and current simultaneous | | | Environmental Specifications | | Operating temperature | | | Storage temperature | | | Humidity (Without Condensation) | | 95% (10ºC to 30ºC) | | 75% (30ºC to 40ºC) | | 45% (40ºC to 50ºC) | | 35% (50ºC to 55ºC) | | | Operating Altitude | | | Safety Specifications | | Safety | | CSA C22.2 No. 1010.1:1992 | | | Maximum voltage | | | Mechanical & General Specifications | | Size | | 216 mm L x 94 mm W x 67 mm (8.5 in. L X 3.72 in. W X 2.61in.) | | | Weight | | | Warranty | | | Shock & Vibration | | Random, 2G, 5-500 Hz | | 1m drop test | | | Battery type | | Two 9V batteries, ANSI/NEDA 1604A or IEC 6LR61 | | Battery life: 4 to 20 hours, typical, depending on functions | | |